SEADOO VTS GUAGES MANUAL
If you're installing an impeller on a Sea Doo, don't follow the manual when it calls for red loctite on the threads. If you've bought one of our carb kits, a great page by GroupK that details the procedures for carb fine tuning can be found HERE If you find an item on another site for less though let us know so we can fix that! Looking for a discount coupon? Our prices are already 10-20% less than everyone else so we don't play that game. YOU THEN CAN ENTER YOUR CC INFO WITHOUT HAVING TO SET UP A PAYPAL ACCOUNT. TO USE YOUR CREDIT CARD SELECT PAYPAL FOR YOUR PAYMENT METHOD THEN ONCE REDIRECTED THERE CLICK THE BUTTON THAT SAYS "PAY WITH CREDIT/DEBIT CARD". We accept Visa, Mastercard, Discover, and AmEx credit cards through PayPal WHAT YOU ENTER FOR SHIPPING IS WHERE IT'S GOING TO GO SO MAKE SURE THAT'S RIGHT BEFORE SUBMITTING YOUR PAYMENT! LATELY WE'VE HAD A BUNCH OF PEOPLE ENTERING THE WRONG SHIPPING ADDRESS INTO THE SITE WHEN ORDERING. ANY EMAIL INQUIRIES ALSO WILL BE ANSWERED TUESDAY THROUGH FRIDAY. ANY ORDERS PLACED OVER THE 3-DAY WEEKEND WILL BE PROCESSED AS SOON AS WE ARE OPEN TUESDAY. If nothing happens on one of the two, then the relay may be bad.NOTE WE ARE NOW IN OUR FALL SCHEDULE WHERE WE ARE CLOSED MONDAYS. Nozzle would 'unscrew' in the lowest position and would not come back up without physical help.
Unfortunately this disabled the gauge and limit stops were not active. Previous owner ended up cutting all the wires off the module and wiring his cheap relay fix. Using a jumper wire from the purple wire to either blue/white or green white, the voltage on your meter will go from +12v to -12v and you'll hear the relays click, depending on which wire you activate. So i picked up my first seadoo, turned out vts was busted.Connect the purple wire to the 12v supply (ignition powers the module up through purple normally).Note that the specs above were found online so may have errors. The motor should draw 1.7A when running and 3.8A peak.
Trim Motor Wires: Green/orange to blue/orange 0 ohms in both directions. Connect the red and black wires to a 12v supply. With VTS in middle position the resistance should be between 24.3 and 171.3 ohms (goes in steps of 14.7 ohms).These wires are normally connected to the trim motor. Connect a voltmeter between the green/orange and blue/orange wires and set it to a scale that reads 12v.Remove the module from the grey box and proceed as follows: This test procedure doesn't check the load sensing, but does make sure the up/down relays are functioning properly. The way I believe the module works is to sense a load when trim reaches limits, and disconnect power from the motor. I've found this is the quickest way to find out if this unit is working properly. The following procedures test the VTS module that's located in the grey box of certain 1993-1995 models. The area above is always changing so check back often as links are added. Hopefully this page will help others avoid the same fate!ĬOMING SOON… Module Conversion Kits for 204470139 204470155 204470179 204470184 MPEMs Have you had a bad experience with a dealer, repair shop, or engine rebuilder? If so, now you can post your experiences here.
If you have one, contact me with description and price. If you have parts or know of a Sea Doo dealer in your area that is closing, contact me at with the details.īlown or wrecked Sea Doo watercraft in the Ohio vicinity. Parts Inventories from overstocked or closing Sea Doo shops.
SEADOO VTS GUAGES PLUS
Sea Doo 278000029 / 278000358 VTS Module Test Procedure My friends at have many hard to find parts in stock as well as custom kits for your Sea Doo plus they ship all over the world so check them out for your Sea Doo parts needs!